SWP-WRC3.2 ratti paneli CAN / Steering Wheel membrane panel

  • €1.359,00
    Yksikköhinta kohti 
Sisältää veron. Toimituskulut lasketaan kassalla.


Huom. FIA säännön mukaan ratin puolia ei saa muokata.
  • Suunniteltu Sabelt 330 ALU ratille, jonka halkaisija 330 mm
  • 1 kpl CAN, Mbit/s, 2.0B
  • Väylä nopeus valittavissa: 1 Mbit/s, 500 kbit/s, 250 kbit/s, 200 kbit/s, 125 kbit/s ja 100 kbit/s
  • 120 Ω päätevastus
  • Oikosulkusuojaus
  • 1 kpl digitaalinen sisääntulo
  • Sisääntulovastus: 4.7 kΩ (5V pull-up)
  • 8 kpl painonappeja, taustavalot ja 2 kpl LED valoja
  • Napin tila lähetetään CAN viestinä
  • 2 kpl kiertokytkimiä, tila lähetetään CAN viestinä
  • 2 kpl On–Off drivers
  • High side driver Vbattery, up to 1 A
  • Output voltage reread
  • Linear current limitation
  • Oikosulkusuoja
  • Ylikuorma ja lämpötila hälytys ja suoja
  • 2 kpl LED tilaväriä napeissa (punainen – vihreä)
  • Aktivointi CAN viesteinä
  • Kaikki LED velot voidaan määritellä napin asennosta riippumatta
  • LED valon kirkkaus määriteltävissä ohjelmalla
  • 6 kpl väri LED:ä kiertokytkimissä
  • LED värejä voidaan muokata tilauksesta
  • Näyteresoluution 10 bit
  • Lämpötila-alue: -40 / +120 °C
  • 2 kpl High side switch outputs voltage reread
  • Jännite partition 20 mV
  • Analogia anti aliasing filter
  • Tarrat tilauksesta
  • 20 cm johto ASL606-05PB liittimellä,. Vastaliitin (ASL106-05SB) tilattavissa erikseen. 
  • Runko billet alumiini ja ABS kuori
  • IP54 roiskesuojattu
  • Paino 245 g

Membrane Steering Wheel Panel

Designed for Sabelt 330 ALU steering wheel. Steering wheel diameter 330 mm.

Note! FIA regulation doesn't allow modification of steering wheel.

1 CAN line

  • 1 Mbit/s throughtput data rate. 2.0B protocol.
  • Selectable bus speeds: 1 Mbit/s and 500, 250, 200, 125 and 100 kbit/s
  • Software selectable 120 Ω terminator
  • Protection against short circuit to ground and battery

1 Digital input for programming enable (ENCP)

  • Input resistance: 4.7 kΩ (5V pull-up)

Upto 8 Keyboard buttons

  • With backlighting
  • With integrated 2 – color gauge LED
  • Button state transmitted on CAN

2 Mechanical rotary switches

  • Compact design – PCB mounted
  • Switch state transmitted on CAN
  • Mechanical endless with electrical „smart stop“ feature
  • Number of positions adjustable by SW

2 On–Off drivers

  • High side driver Vbattery, up to 1 A
  • Output voltage reread
  • Linear current limitation
  • Protection against short circuit to ground
  • Overload, over temperature feedback and protection

Upto 10 Gauge LEDs

  • 2 color state (red – green)
  • Integrated in keyboard buttons
  • Activation received from CAN
  • Each LED controlled independently from button
  • LED color adjustable by SW within red – green scale
  • Brightness adjustable by SW

2 Status Gauge LED groups at rotary switches

  • 6 single colour LEDs at each rotary switch
  • Each LED group has its independent control – internally (by firmware) or via CAN
  • Position can be memorized at power off
  • LED colors can be modified on request (HW modification)

1 Internal temperature

  • Sampling resolution: 10 bits
  • Temperature range: -40 / +120 °C

2 High side switch outputs voltage reread

  • Sampling resolution: 10 bits
  • Voltage partition 20 mV
  • Analogue anti aliasing filter

Overall dimensions

  • Without cable: 189 x 118 x 24 mm
  • Including rotary knobs: 189 x 118 x 39 mm
  • 20 cm cable with ASL606-05PB connector,. Mating connector (ASL106-05SB) available separately

Enclosure

  • Machined aluminum / ABS cover
  • IP grade: IP54

Weight (without steering wheel)

  • approx 245 g

Panel mounting on steering wheel usually by cable ties.

Keyboard layout, shape

  • Layout - button positions are optimised to be easillyreachable with the thumb keeping the hand on handgrip
  • Laout graphics is an integral part of the membrane applied by seriography
  • Relief of buttons are heighten by applying silicone caps on the top of the buttons (height increase upto cca 1.5 mm)